188宝金博页面版

Designation: B 396 – 00Standard Specif i cation forAluminum-Alloy 5005-H19 Wire for Electrical Purposes 1This standard is issued under the f i xed designation B 396; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specif i cation covers aluminum alloy 5005-H19(extra hard) round wire for electrical purposes.1.2 The SI values of density and resistivity are to beregarded as standard. For all other properties, the inch-poundvalues are to be regarded as standard, and the SI units may beapproximate.N OTE 1—The alloy and temper designations conform to ANSI H35.1.Aluminum alloy 5005 corresponds to Unif i ed Numbering System alloyA95005 in accordance with Practice E 527.2. Referenced Documents2.1 The following documents of the issue in effect on dateof material purchase form a part of this specif i cation to theextent referenced herein:2.2 ASTM Standards:B 193 Test Method for Resistivity of Electrical ConductorMaterials 2B 354 Terminology Relating to Uninsulated Metallic Elec-trical Conductors 2B 531 Specif i cation for Aluminum-Alloy 5005 DrawingStock for Electrical Purposes 2B 557 Test Methods of Tension Testing Wrought and CastAluminum- and Magnesium-Alloy Products 3E 29 Practice for Using Signif i cant Digits in Test Data toDetermine Conformance with Specif i cations 4E 527 Practice for Numbering Metals and Alloys (UNS) 52.3 Other Documents:ANSI H35.1 American National Standard for Alloy andTemper Designation Systems for Aluminum 6NBS Handbook 100—Copper Wire Tables of the NationalBureau of Standards73. Ordering Information3.1 Orders for material under this specif i cation shall includethe following information:3.1.1 Quantity of each size,3.1.2 Wire diameter (see 9.1),3.1.3 When tension tests of wires containing joints shall bemade (see 5.2 and 5.3),3.1.4 Frequency of bending test, when required (see 6.2),3.1.5 Special jointing procedures, if permitted, (see 10.2),3.1.6 Package size and type (see 15.1),3.1.7 Special package marking, if required (see 16.1), and3.1.8 Place of inspection (Section 14).4. Material4.1 The wire shall be made from rod meeting the require-ments of Specif i cation B 531.5. Tensile Requirements5.1 The wire shall be sampled in accordance with Section12 and tested in accordance with Test Methods B 557. The wireshall conform to the requirements as to tensile propertiesprescribed in Table 1 (Explanatory Note 1). The elongation ofwire shall be determined as the permanent increase in length,due to the breaking of the wire in tension, measured betweengage marks placed originally 10 in. (250 mm) apart upon thetest specimen.5.2 When requested by the purchaser, tension tests shall bemade on specimens of f i nished wire containing joints made inthe wire prior to f i nal drawing or in the rod. Such tests shallshow not less than 90 % of the minimum strength specif i ed inTable 1 for individual tests.5.3 When requested by the purchaser, tension tests off i nished wire specimens containing joints made in the f i nishedwire or during f i nal drawing, as permitted in 10.2, shall bemade. Such tests shall show the tensile strength to be not less1 This specif i cation is under the jurisdiction of ASTM Committee B-1 onElectrical Conductors, and is the direct responsibility of Subcommittee B01.07 onConductors of Light Metals.Current edition approved April 10, 2000. Published June 2000. Originallypublished as B 396 – 63 T. Last previous edition B 396 – 87 (1994).2 Annual Book of ASTM Standards, Vol 02.03.3 Annual Book of ASTM Standards, Vol 02.02.4 Annual Book of ASTM Standards, Vol 14.02.5 Annual Book of ASTM Standards, Vol 01.01.6 Available from the American National Standards Institute, 11 West 42nd St.,13th Floor, New York, NY 10036.7 Available from the National Technical Information Service, 5285 Port RoyalRd., Springf i eld, VA 22161.1Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.NOTICE: This standard has either been superceded and replaced by a new version or discontinued. Contact ASTM International (www.astm.org) for the latest information.