Designation: F3077 − 17Standard Specif i cation forEye Protectors for Women’s Lacrosse 1This standard is issued under the f i xed designation F3077; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (´) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specif i cation covers eye protectors designed for useby players of women’s lacrosse that minimize or signif i cantlyreduce injury to the eye and adnexa due to impact andpenetration of lacrosse balls. Protective eyewear offers protec-tion only to the eyes and does not protect other parts of thehead.1.2 Impact testing is done in a laboratory setting. Eyecontact is determined by observation.1.3 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly. Metric units of measurement in this specif i cation are inaccordance with the International System of Units (SI). If avalue for measurement as given in this specif i cation is followedby an equivalent value in other units, the f i rst stated is to beregarded as the requirement. A given equivalent value may beapproximate.1.4 The following precautionary caveat pertains only to thetest methods portion (Sections 8, 9, and 10) of this specif i ca-tion: This standard does not purport to address all of the safetyconcerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety,health, and environmental practices and determine the appli-cability of regulatory limitations prior to use.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards: 2D1003 Test Method for Haze and Luminous Transmittanceof Transparent Plastics2.2 ANSI Standards: 3ANSI Z80.1 Requirements for First-Quality PrescriptionOphthalmic LensesANSI Z80.3 Nonprescription Sunglasses and Fashion Eye-wear RequirementsANSI Z87.1 Occupational and Educational Personal Eyeand Face Protection Devices2.3 Federal Standard: 4National Institute of Standards and Technology SpecialTechnical Publication 374 Method for Determining theResolving Power of Photographic Lenses2.4 Canadian Standard: 5CSA Z262.6-14 Specif i cations for Facially Featured HeadForms2.5 NOCSAE Standard: 6NOCSAE (ND) 049 Standard Performance Specif i cation forNewly Manufactured Lacrosse Balls3. Terminology3.1 Def i nitions of Terms Specif i c to This Standard:3.1.1 binocular, adj—relating to the f i eld of view which isshared by both eyes simultaneously; also any simultaneousactivity of the two eyes.3.1.2 central viewing zone, n—that part of the eye of aprotector which has its center in line with the wearer’s normalline of sight.3.1.2.1 Discussion—The zone is circular in shape, and 40mm in diameter. The center of the central viewing zone shall bethe point of intersection of the line of sight with the lens asmounted on the CSA headform. (See CSA Z262.6.)3.1.3 cleanable, n—ability of a protective device to be madereadily free of dirt or grime without being damaged during anappropriate cleaning process, such as the use of soap and water.1 This specif i cation is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct responsibility ofSubcommittee F08.57 on Eye Safety for Sports.Current edition approved July 1, 2017. Published October 2017. Originallyapproved in 2014. Last previous edition approved in 2014 as F3077 – 14. DOI:10.1520/F3077-17.2 For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at service@astm.org. For Annual Book of ASTMStandards volume information, refer to the standard’s Document Summary page onthe ASTM website.3 Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http://www.ansi.org.4 Available from National Institute of Standards and Technology (NIST), 100Bureau Dr., Stop 1070, Gaithersburg, MD 20899-1070, http://www.nist.gov.5 Available from Canadian Standards Association (CSA), 5060 Spectrum Way,Mississauga, ON L4W 5N6, Canada, http://www.csa.ca.6 Available from the National Operating Committee on Standards for AthleticEquipment (NOCSAE), http://www.nocsae.org.Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1
