Designation: F2987 − 12 An American National StandardStandard Specif i cation forCorrugated Polyethylene Pipe and Fittings for Mine HeapLeach Aeration Applications 1This standard is issued under the f i xed designation F2987; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (´) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specif i cation covers requirements and test methodsfor materials, workmanship, dimensions, perforations, pipestiffness, elongation, joint separation resistance, quality ofextruded polyethylene, brittleness, testing, and marking ofcorrugated polyethylene (PE) pipe and f i ttings for mine heapleach pile aeration. It covers with nominal sizes 100 mm (4inch), 150 mm (6 inch), 200 mm (8 inch), 250 mm (10 inch)300 mm (12 inch), 375 mm (15 inch), and 450 mm (18 inch)diameter.1.2 This specif i cation covers double wall, annular extrudedcorrugated polyethylene pipe as depicted in Fig. 1.1.3 The values given in parentheses are provided for infor-mation purposes only.1.4 The following precautionary caveat pertains only to thetest method portion, Section 9, of this specif i cation: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards: 2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of Thermoplastic Pipe and Fittings by Means of aTup (Falling Weight)D3350 Specif i cation for Polyethylene Plastics Pipe and Fit-tings MaterialsD3895 Test Method for Oxidative-Induction Time of Poly-olef i ns by Differential Scanning CalorimetryF412 Terminology Relating to Plastic Piping SystemsF2136 Test Method for Notched, Constant Ligament-Stress(NCLS) Test to Determine Slow-Crack-Growth Resis-tance of HDPE Resins or HDPE Corrugated Pipe2.2 Federal Standards: 3Fed. Std. No. 123 Marking for Shipment (Civil Agencies)Federal Emergency ManagementAgency (FEMA) TechnicalManual: Plastic Pipe Used in Embankment Dams: BestPractices for Design, Construction, Problem Identif i cationand Evaluation, Inspection, Maintenance, Renovation, andRepair2.3 Military Standard: 3MIL-STD-129 Marking for Shipment and Storage3. Terminology3.1 Def i nitions—Def i nitions used in this specif i cation are inaccordance with Terminology F412 and abbreviations are inaccordance with Terminology D1600, unless otherwise speci-f i ed. The abbreviation for polyethylene is PE.3.2 Def i nitions of Terms Specif i c to This Standard:3.2.1 split—any break or crack that extends through thewall.3.2.2 crease—a deformation that cannot be removed like adent: generally associated with wall buckling.3.2.3 leaching—minerals are removed (leached) from oresthat have been mined, crushed, and placed on impervious padsfor removal (by chemical leaching) by percolation of thesolution through the ore, and collection of that solution at thebottom of the heap leach pile.4. Ordering Information4.1 Orders for product made to this specif i cation shallinclude the following information to adequately describe thedesired product:1 This test method is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.26 on Olef i nBased Pipe.Current edition approved Nov. 1, 2012. Published February 2013. DOI: 10.1520/F2987-12.2 For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at service@astm.org. For Annual Book of ASTMStandards volume information, refer to the standard’s Document Summary page onthe ASTM website.3 Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1
