188宝金博页面版

LEXAN* Resin 141R Europe-Africa-Middle East: COMMERCIAL LEXAN 1 41 R is a medium viscosity multi purpose grade and contains a release agent to ensure easy processing. LEXAN 1 41 R is available in transparent,translucent and opaque colours. TYPICAL PROPERTIES ¹TYPICAL VALUEUNITSTANDARD MECHANICALTaber Abrasion, CS-1 7, 1 kg1 0mg/1 000cyGE MethodTensile Stress, yield, 50 mm/min63MPaISO 527Tensile Stress, break, 50 mm/min70MPaISO 527Tensile Strain, yield, 50 mm/min6%ISO 527Tensile Strain, break, 50 mm/min1 1 0%ISO 527Tensile Modulus, 1 mm/min2350MPaISO 527Flexural Stress, yield, 2 mm/min90MPaISO 1 78Flexural Modulus, 2 mm/min2300MPaISO 1 78Hardness, H358/3095MPaISO 2039-1 IMPACT Izod Impact, unnotched 80*1 0*4 +23°CNBkJ/m²ISO 1 80/1 U Izod Impact, unnotched 80*1 0*4 -30°CNBkJ/m²ISO 1 80/1 U Izod Impact, notched 80*1 0*4 +23°C1 2kJ/m²ISO 1 80/1 A Izod Impact, notched 80*1 0*4 -30°C1 0kJ/m²ISO 1 80/1 A Charpy Impact, notched, 23°C35kJ/m²ISO 1 79/2C Charpy 23°C, Unnotch Edgew 80*1 0*4 sp=62mmNBkJ/m²ISO 1 79/1 eU Charpy -30°C, Unnotch Edgew 80*1 0*4 sp=62mmNBkJ/m²ISO 1 79/1 eU THERMALThermal Conductivity0.2W/m-°CISO 8302 CTE, 23°C to 80°C, flow7.E-051 /°CISO 1 1 359-2 Ball Pressure Test, 1 25°C +/- 2°CPASSES-IEC 60695-1 0-2Vicat Softening Temp, Rate A/501 53°CISO 306Vicat Softening Temp, Rate B/501 41°CISO 306Vicat Softening Temp, Rate B/1 201 42°CISO 306HDT/Be, 0.45MPa Edgew 1 20*1 0*4 sp=1 00mm1 36°CISO 75/BeHDT/Ae, 1 .8 MPa Edgew 1 20*1 0*4 sp=1 00mm1 25°CISO 75/AeRelative Temp Index, Elec1 30°CUL 746BRelative Temp Index, Mech w/impact1 25°CUL 746BRelative Temp Index, Mech w/o impact1 25°CUL 746B PHYSICALMold Shrinkage on Tensile Bar, flow (2)0.5 - 0.7%GE MethodDensity1 .2g/cm³ISO 1 1 83Source, GMD, Last Update:1 1 /06/2000PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA All information, recommendation or advice given by General Electric Company USA, or any of its subsidiaries, affiliates orauthorized representatives, whether written or oral, is given in good faith, to the best of its knowledge and based on current procedures in effect. Each user of the products shall convince himself, through allavailable sources (including finished product testing in its appropriate environment) of the suitability of the products supplied for its own particular purpose. Because actual use of the products by the user isbeyond the control of General Electric Company, its subsidiaries and affiliates, such use is in the exclusive responsibility of the user. General Electric Company, its subsidiaries and affiliates cannot be heldresponsible respectively liable for any loss incurred through incorrect or faulty use of the products. Information, recommendations and/or advice are neither made to infringe on any patents, nor to grant a licenseunder any patent or intellectual property right of General Electric Company or any of its subsidiaries or affiliated companies, nor to grant the right to file for any patent protection* LEXAN is a trademark of the General Electric Company© 1 997-2005 General Electric Company.All rights reserved1 )Typical values only. Variations within normal tolerances are possible for variose colours.All values aremeasured at least after 48 hoursstorage at 230C/50% relative humidity.All properties, expect the melt volume rate are measured on injectionAll samples are prepared according to ISO 294.moulded samples.2)Only typical data for material selection purpose.Not to be used for3)This rating is not intended to reflect hazards presented by this or any4)Own measurement according to UL.part or tool design.other material under actual fire conditions.