Designation: F467M − 06a (Reapproved 2012)Standard Specif i cation forNonferrous Nuts for General Use (Metric) 1This standard is issued under the f i xed designation F467M; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (´) indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specif i cation covers the requirements for commer-cial wrought nonferrous nuts in nominal thread diameters M6to M36 inclusive in a number of alloys in common use andintended for general service applications.1.2 Applicable bolts, cap screws, and studs for use with nutscovered by this specif i cation are covered by Specif i cationF468M.1.3 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.N OTE 1—This specif i cation is the metric companion of Specif i cationF467.2. Referenced Documents2.1 ASTM Standards: 2B154 Test Method for Mercurous Nitrate Test for CopperAlloysB574 Specif i cation for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy RodD3951 Practice for Commercial PackagingE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsE29 Practice for Using Signif i cant Digits in Test Data toDetermine Conformance with Specif i cationsE34 Test Methods for Chemical Analysis of Aluminum andAluminum-Base AlloysE38 Methods for Chemical Analysis of Nickel-Chromiumand Nickel-Chromium-Iron Alloys (Withdrawn 1989) 3E53 Test Method for Determination of Copper in UnalloyedCopper by GravimetryE54 Test Methods for Chemical Analysis of Special Brassesand Bronzes (Withdrawn 2002) 3E55 Practice for Sampling Wrought Nonferrous Metals andAlloys for Determination of Chemical CompositionE62 Test Methods for Chemical Analysis of Copper andCopperAlloys (Photometric Methods) (Withdrawn 2010) 3E75 Test Methods for Chemical Analysis of Copper-Nickeland Copper-Nickel-Zinc Alloys (Withdrawn 2010) 3E76 Test Methods for Chemical Analysis of Nickel-CopperAlloys (Withdrawn 2003) 3E92 Test Methods for Vickers Hardness and Knoop Hard-ness of Metallic MaterialsE101 Test Method for SpectrographicAnalysis ofAluminumand Aluminum Alloys by the Point-to-Plane Technique(Withdrawn 1996) 3E120 Test Methods for Chemical Analysis of Titanium andTitanium Alloys (Withdrawn 2003) 3E165 Practice for Liquid Penetrant Examination for GeneralIndustryE227 Test Method for Optical Emission SpectrometricAnalysis of Aluminum and Aluminum Alloys by thePoint-to-Plane Technique (Withdrawn 2002) 3E354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron,Nickel, and Cobalt AlloysE478 Test Methods for Chemical Analysis of Copper AlloysE1409 Test Method for Determination of Oxygen and Nitro-gen in Titanium and Titanium Alloys by Inert Gas FusionF468M Specif i cation for Nonferrous Bolts, Hex Cap Screws,and Studs for General Use (Metric)F606M Test Methods for Determining the Mechanical Prop-erties of Externally and Internally Threaded Fasteners,Washers, and Rivets (Metric)F1470 Practice for Fastener Sampling for Specif i ed Me-chanical Properties and Performance Inspection1 This specif i cation is under the jurisdiction of ASTM Committee F16 onFasteners and is the direct responsibility of Subcommittee F16.04 on NonferrousFasteners.Current edition approved April 1, 2012. Published May 2012. Originallyapproved in 1979. Last previous edition approved in 2006 as F467M – 06aε2 . DOI:10.1520/F0467M-06R12.2 For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at service@astm.org. For Annual Book of ASTMStandards volume information, refer to the standard’s Document Summary page onthe ASTM website.3 The last approved version of this historical standard is referenced onwww.astm.org.*A Summary of Changes section appears at the end of this standardCopyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1 Copyright by ASTM Int'l (all rights reserved); Thu Aug 3 12:39:34 EDT 2017Downloaded/printed byUniversity of Edinburgh (University of Edinburgh) pursuant to License Agreement. No further reproductions authorized.
